Bedienungsanleitung 3M FSTMO75 Water System

Bedienungsanleitung für das Gerät 3M FSTMO75 Water System

Bedienungsanleitung 3M FSTMO75 Water System

Auszüge von Inhalten

Inhalt Zusammenfassung auf der Seite No. 1

3M™ Water Filtration ProductsFlashGARD HP™ Reverse Osmosis Filtration SystemModel Number FSTMO75Part Number 56123-06Installer: Please leave this manual with owner/operator.End User: Please retain for operation and future maintenance instructions.1

Inhalt Zusammenfassung auf der Seite No. 2

3M™ Water Filtration ProductsSAFETY INFORMATIONRead, understand, and follow all safety information contained in these instructions prior to installation and use of the Reverse Osmosis WaterTreatment System. Retain these instructions for future reference.Intended use: The FlashGARD-HP FSTMO75 Water Treatment System is intended for use in filtering potable water for food service coffee, espresso andsteamer equipment and has not been evaluated for other uses. The system is typically installed nea

Inhalt Zusammenfassung auf der Seite No. 3

Table of ContentsSafety Instructions ................................................................................................................................................................ Page 2Caution and Warning Statements............................................................................................................................................ Page 2Parts List.............................................................................................................

Inhalt Zusammenfassung auf der Seite No. 4

MountingCAUTIONTo reduce the risk associated with property damage due to water leakage:• Before starting installation, shut off main water supply and drain pipes.• Take care when using pliers or pipe wrenches to tighten plastic fittings, as damage may occur if overtightening occurs.• Do not install in direct sunlight or outdoors.• Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount the bracket.• Mount filter in such a position a

Inhalt Zusammenfassung auf der Seite No. 5

Plumbing ConnectionsCAUTION : The FlashGard-HP Reverse Osmosis Water Filtration System requires a minimum 60 psi (413.7 kPa) inlet water pressure. To ensure adequate inlet water pressure, it is recommended that the system be plumbed after the beverage booster pumpbut before the beverage water filtration system. Refer to Figure 2 for proper tubing connections.CAUTION: Use care in routing the tubing to ensure that there are no bends or kinks.CAUTIONTo reduce the risk associated with property damag

Inhalt Zusammenfassung auf der Seite No. 6

Using Push-In FittingsTo Attach TubingPush tubing in as far as it will go. Tubing must be inserted pasto-ring and hit backstop. Pull tube to ensure it is secured.1To Release TubingPush in grey collet to release tubing. With collet held,pull tubing straight out.212CAUTIONTo reduce the risk associated with property damage due to water leakage:• Ensure all tubing and fittings are secure and free of leaks.• Do not install unit if collet is missing. Contact 3M if collets are missing from any fitt

Inhalt Zusammenfassung auf der Seite No. 7

RO Membrane Cartridge (Replace every 24-36 months) continued4) Pull down on RO cartridge.5) Discard used RO cartridge.6) Remove red cap from new RO cartridge and moisten the o-ring with water.7) Insert new RO cartridge into the filter head. Be sure that the ears on the cartridge line up with the spaces in the head.8) Turn new cartridge 1/4 turn to the right.9) Open tank shut-off and inlet valves (see Figure 2)10) Divert the Water Sample Valve outlet to drain.Open valve and let water run through

Inhalt Zusammenfassung auf der Seite No. 8

Troubleshooting GuideProblemCauseNotesSolutionRepair Beverage BoosterPump/SystemContact DealerAdd Booster Pump AssemblyOnly if Beverage Booster System isnot installedRO Membrane FouledReplace RO Module and SFCTubing (Stealth Flow Control)Feed Water Pressure, Temperature,RO Module Flow Rate and RejectWater should be checkedStorage Tank Air Chargeis LowDrain Tank using Sample Valve,with Sample Valve Open, Pumpup Air Charge, 8 -10 psi (55.2- 68.9 kPa), close Sample ValveUnscrew Blue Cap to access S

Inhalt Zusammenfassung auf der Seite No. 9

9

Inhalt Zusammenfassung auf der Seite No. 10

10

Inhalt Zusammenfassung auf der Seite No. 11

11

Inhalt Zusammenfassung auf der Seite No. 12

Warranty and Limited Remedy:THE FOLLOWING WARRANTIES ARE MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY,THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR USAGE OF TRADE:CUNO Incorporated warrants this Product to be free from defects in material and workmanship to the original end-user when installed in accordance with the Installation a

HINTERLASSE EINEN KOMMENTAR